First, make sure that you have disconnected all hoses, extensions, or additional valves from the faucet or faucets you plan on winterizing to allow water to escape.

Second, find your shutoff valve or valves for each exterior faucet and turn them to the shutoff or off position.

Third, return to the exterior of the home and open each faucet. Leave each faucet(s) open for a short while to ensure all water has had the opportunity to escape.

Lastly, once you have allowed the faucet to remain open for a short while, close the valve entirely if it is a frost free hose bib. If it is not a frost free hose bib leave the valve just slightly open. This is the part sometimes debated in the winterization process but as most plumbers or contractors familiar with this process will tell you, it is not the just the water itself but the accumulated pressure created by the freezing and expanding water that creates most pipes from busting.

There you have it. A quick, simple and effective method to winterizing your exterior hose bibs. Have this process done before consisentent freezing temperatures and rest easy.

• Federal, state, utility and local jurisdictions’ financial incentives, such as tax breaks, are very advantageous in most parts of the U.S.
• It saves money. It costs less to power a home that has been converted to be more energy-efficient.
• It increases indoor comfort levels.
• It reduces our impact on climate change. Many scientists now believe that excessive energy consumption contributes significantly to global warming.
• It reduces pollution. Conventional power production introduces pollutants that find their way into the air, soil and water supplies.

1. Find better ways to heat and cool your house.
   As much as half of the energy used in homes goes toward heating and cooling. The following are a few ways that energy bills can be reduced through adjustments to the heating and cooling systems:
   • Install a ceiling fan. Ceiling fans can be used in place of air conditioners, which require a large amount of energy.
   • Periodically replace air filters in air conditioners and heaters.
   • Set thermostats to an appropriate temperature. Specifically, they should be turned down at night and when no one is home. In most homes, about 2% of the heating bill will be saved for each degree that the thermostat is lowered for at least eight hours each day. Turning down the thermostat from 75° F to 70°F, for example, saves about 10% on heating costs.
   • Install a programmable thermostat. A programmable thermostat saves money by allowing heating and cooling appliances to be automatically turned down during times that no one is home and at night. Programmable thermostats contain no mercury and, in some climate zones, can save up to $150 per year in energy costs.
   • Install a wood stove or a pellet stove. These are more efficient sources of heat than furnaces.
   • At night, curtains drawn over windows will better insulate the room.
2. Install a tankless water heater.
   Demand water heaters (tankless or instantaneous) provide hot water only as it is needed. They don’t produce the standby energy losses associated with storage water heaters, which will save on energy costs. Demand water heaters heat water directly without the use of a storage tank. Therefore, they avoid the standby heat losses required by traditional storage water heaters. When a hot water tap is turned on, cold water travels through a pipe into the unit. Either a gas burner or an electric element heats the water. As a result, demand water heaters deliver a constant supply of hot water. You don’t need to wait for a storage tank to fill up with enough hot water.
3. Replace incandescent lights.
   The average household dedicates 11% of its energy budget to lighting. Traditional incandescent lights convert approximately only 10% of the energy they consume into light, while the rest becomes heat. The use of new lighting technologies, such as light-emitting diodes (LEDs) and compact fluorescent lamps (CFL), can reduce energy use required by lighting by 50% to 75%. Advances in lighting controls offer further energy savings by reducing the amount of time lights are on but not being used. Here are some facts about CFLs and LEDs:
   • CFLs use 75% less energy and last about 10 times longer than traditional incandescent bulbs.
   • LEDs last even longer than CFLs and consume less energy.
   • LEDs have no moving parts and, unlike CFLs, they contain no mercury.
4. Seal and insulate your home.
   Sealing and insulating your home is one of the most cost-effective ways to make a home more comfortable and energy efficient — and you can do it yourself. A tightly sealed home can improve comfort and indoor air quality while reducing utility bills. An InterNACHI energy auditor can be hired to assess envelope leakage and recommend fixes that will dramatically increase comfort and energy savings.
   The following are some common places where leakage may occur:
   • electrical outlets;
   • mail slots;
   • around pipes and wires;
   • wall- or window-mounted air conditioners;
   • attic hatches;
   • fireplace dampers;
   • weatherstripping around doors;
   • baseboards;
   • window frames; and
   • switch plates.

   Because hot air rises, air leaks are most likely to occur in the attic. Homeowners can perform a variety of repairs and maintenance to their attics that save them money on cooling and heating, such as:

   • Plug the large holes. Locations in the attic where leakage is most likely to be the greatest are where walls meet the attic floor, behind and under attic knee walls, and in dropped-ceiling areas.
   • Seal the small holes. You can easily do this by looking for areas where the insulation is darkened. Darkened insulation is a result of dusty interior air being filtered by insulation before leaking through small holes in the building envelope. In cold weather, you may see frosty areas in the insulation caused by warm, moist air condensing and then freezing as it hits the cold attic air. In warmer weather, you’ll find water staining in these same areas. Use expanding foam or caulk to seal the openings around plumbing vent pipes and electrical wires. Cover the areas with insulation after the caulk is dry.
   • Seal up the attic access panel with weatherstripping. You can cut a piece of fiberglass or rigid foam board insulation the same size as the attic hatch and glue it to the back of the attic access panel. If you have pull-down attic stairs or an attic door, these should be sealed in a similar manner.
5. Install efficient shower heads and toilets.
   The following systems can be installed to conserve water usage in homes:
   • low-flow shower heads. They are available in different flow rates, and some have a pause button which shuts off the water while the bather lathers up;
   • low-flow toilets. Toilets consume 30% to 40% of the total water used in homes, making them the biggest water users. Replacing an older 3.5-gallon toilet with a modern, low-flow 1.6-gallon toilet can reduce usage an average of two gallons-per-flush (GPF), saving 12,000 gallons of water per year. Low-flow toilets usually have “1.6 GPF” marked on the bowl behind the seat or inside the tank;
   • vacuum-assist toilets. These types of toilets have a vacuum chamber which uses a siphon action to suck air from the trap beneath the bowl, allowing it to quickly fill with water to clear waste. Vacuum toilets are relatively quiet; and
   • dual-flush toilets. Dual-flush toilets have been used in Europe and Australia for years, and are now gaining in popularity in the U.S. Dual-flush toilets let you choose between a 1-gallon (or less) flush for liquid waste, and a 1.6-gallon flush for solid waste. Dual-flush 1.6-GPF toilets reduce water consumption by an additional 30%.
6. Use appliances and electronics responsibly.
   Appliances and electronics account for about 20% of household energy bills in a typical U.S. home. The following are tips that will reduce the required energy of electronics and appliances:
   • Refrigerators and freezers should not be located near the stove, dishwasher or heat vents, or exposed to direct sunlight. Exposure to warm areas will force them to use more energy to remain cool.
   • Computers should be shut off when not in use. If unattended computers must be left on, their monitors should be shut off. According to some studies, computers account for approximately 3% of all energy consumption in the United States.
   • Use efficient “Energy Star”-rated appliances and electronics. These devices, approved by the DOE and the EPA’s Energy Star Program, include TVs, home theater systems, DVD players, CD players, receivers, speakers and more. According to the EPA, if just 10% of homes used energy-efficient appliances, it would reduce carbon emissions by the equivalent of 1.7 million acres of trees.
   • Chargers, such as those for laptops and cell phones, consume energy when they are plugged in. When they are not connected to electronics, chargers should be unplugged.
   • Laptop computers consume considerably less electricity than desktop computers.
7. Install daylighting as an alternative to electrical lighting.
   Daylighting is the practice of using natural light to illuminate the home’s interior. It can be achieved using the following approaches:
   • skylights. It’s important that they be double-pane or they may not be cost-effective. Flashing skylights correctly is key to avoiding leaks;
   • lightshelves. Light shelves are passive devices designed to bounce light deep into a building. They may be interior or exterior. Light shelves can introduce light into a space up to 2½ times the distance from the floor to the top of the window, and advanced light shelves may introduce four times that amount;
   • clerestory windows.  Clerestory windows are short, wide windows set high on the wall. Protected from the summer sun by the roof overhang, they allow winter sun to shine through for natural lighting and warmth; and
   • light tubes.  Light tubes use a special lens designed to amplify low-level light and reduce light intensity from the midday sun. Sunlight is channeled through a tube coated with a highly reflective material, then enters the living space through a diffuser designed to distribute light evenly.
8. Insulate windows and doors.
   About one-third of the home’s total heat loss usually occurs through windows and doors. The following are ways to reduce energy lost through windows and doors:
   • Seal all window edges and cracks with rope caulk. This is the cheapest and simplest option.
   • Windows can be weatherstripped with a special lining that is inserted between the window and the frame. For doors, weatherstrip around the whole perimeter to ensure a tight seal when closed. Install quality door sweeps on the bottom of the doors, if they aren’t already in place.
   • Install storm windows at windows with only single panes. A removable glass frame can be installed over an existing window.
   • If existing windows have rotted or damaged wood, cracked glass, missing putty, poorly fitting sashes, or locks that don’t work, they should be repaired or replaced.
9. Cook smart.
   An enormous amount of energy is wasted while cooking. The following recommendations and statistics illustrate less wasteful ways of cooking:
   • Convection ovens are more efficient that conventional ovens. They use fans to force hot air to circulate more evenly, thereby allowing food to be cooked at a lower temperature. Convection ovens use approximately 20% less electricity than conventional ovens.
   • Microwave ovens consume approximately 80% less energy than conventional ovens.
   • Pans should be placed on the correctly-sized heating element or flame.
   • Lids make food heat more quickly than pans that do not have lids.
   • Pressure cookers reduce cooking time dramatically.
   • When using conventional ovens, food should be placed on the top rack. The top rack is hotter and will cook food faster.
10. Change the way you wash your clothes.
    • Do not use the “half load” setting on your washer. Wait until you have a full load of clothes, as the “half load” setting saves less than half of the water and energy.
    • Avoid using high-temperature settings when clothes are not that dirty. Water that is 140 degrees uses far more energy than 103 degrees for a “warm” setting, but 140 degrees isn’t that much better for washing purposes.
    • Clean the lint trap before you use the dryer, every time. Not only is excess lint a fire hazard, but it will prolong the amount of time required for your clothes to dry.
    • If possible, air-dry your clothes on lines and racks.
    • Spin-dry or wring clothes out before putting them into a dryer.

Homeowners who take the initiative to make these changes usually discover that the energy savings are more than worth the effort.

• First, locate your water heater and determine if its gas or electric.
• Second, locate your water shut-off valve and turn it off.
• Third, Turn of your heating supply, whether gas or electric and gather your bucket.
• Fourth, locate your drain valve, and pressure relief valve, and attach your hose to the drain valve.
• Fifth, after letting your water heater cool down, open the drain valve and release the water heater into the bucket filling until the water becomes clear and free of sediment. (The reason the above step indicates looking for the pressure relief valve is that it may be necassary to open it if the tank does not drain well. Opening the valve will allow air to enter the tank and water to flow easier)

Lastly, after the water appears clear and the sediment is removed from the tank close the drain valve, refill the tank by opening the water valve. After the tank has been completely filled turn the heating supply on. Come back next year and repeat the process.